SPECIFICATIONS

STRUCTURE

• Fibreglass roving & unidirectional reinforcements over foam floors with limber holes
• Four full-length longitudal floors forming the engine beds
  
• Transverse frames bonded to hull and longitudinal
  

HULL CONSTRUCTION

• Vinylester resin throughout
• Single piece Core-Cell cored fibreglass molding
• Extra reinforcing as required
• Awlgrip painted top sides & boot stripe
• Rub strake at water line
  

DECK CONSTRUCTION

• Single piece Core-Cell cored fibreglass molding with non-skid pattern on all working surfaces
• Core phased out in way of all deck fittings
• Non-skid surfaces finished in moon dust awlgrip
• Hull/deck joint bonded and fastened every four inches
  

DECK HARDWARE

• All deck hardware and fittings of stainless steel or chrome plated bronze
• Custom fabricated channel type bow fitting to accommodate two anchors
• Maxwell or Lewmar electric windlass
• Custom cast fairlead chocks for bow, stern and spring lines
• 8 x 12" mooring cleats
•  Custom fabricated 1 1/4" dia. bow and side rail and stanchoins with gates P&S
• Custom fabricated rails in way of steps to fly bridge
• Teak decking in aft cockpit, on aft house top landing, and on fly bridge deck
• Custom fabricated swim platform with teak deck and s.s swim ladder
• Varnished teak cap on bulwarks
• Varished teak moulding on trunk cabins, main salon sides and roof
• Varnished teak handrails as required
  

•  Custom fabricated s.s. and plexiglass fly bridge windshield
• Tempered glass pilot house / main salon windows
• 3 pantograph type windsheild wipers with washing system
• Two sliding pilot house doors to side decks with screens
• Teak framed aft main salon dorr to aft house top
• Transom door to swim platform
• Stainless steel opening ports with screens
• Stainless steel or polished anodized aluminium deck hatches with screens
  

ENGINE & DRIVE SYSTEM

• Twin Caterpillar 3196 DITA 660 HP Diesel engines with ZF 325A - 2.037 :1 red'n gears (7 deg. angle)
• Engine instrument panel at pilothouse and fly bridge helm stations with tachometer, hour meter, ammeter, oil presseure and temperature gauges for each engine
• Mathers throttle and gear controls at both helm stations
• 2 1/4" dia. Aquamet 22 propeller shafts
  

STEERING

• Teleflex hydraulic steering for two helm stations, in pilothouse and on fly bridge
• Twin rudders custom fabricated cast in bronze
• Side-Power SP155 TC 24V twin prop thruster with controls at both helm stations
  

PLUMBING & REFRIGERATION

• 24/ 110V refrigeration system Sea Frost or equivalent
• FRP boxes with 4" foamed in place insulation and vapor barrier; all openings gasketed
• "Day" refigeration in galley front opening; large storage refrgerator and freezer front opening utility space
• Three 16,000 BTU reverse cycle 110V air conditioning units
• Cruisair or equivalent air conditioning ducting, plenums and vents as required
  

• Pressure water with 24V pumps, filters and accumulator tanks suplying faucets in heads, showers and galley
• Hot water heater - 30 US gal
• Foot pumps for fresh and salt water in galley
• Two ss fresh water tanks for total capacity of 300 gal
• Clothes washer/dryer combntation unit (ducted) in utility space
• Two showers with FRP sumps, 24V sump pumps and telephone shower heads
• Deep double s.s. sink in galley
• Corian sinks in heads
• All plumbing and couplers are PVC
• All shut off and diverter valves easily accessible
  

• Two Headhunter heads
• Two 50 US gal. holding tanks, with deck pump-outs and vents
• Two 24V waste pumps with overboard discharges
  

• Three Jabsco 4000 HD or equivalent 24V bilge pumps with float switches
  

• Barrel or ball type sea cocks with flanged bodies on all below water thru-hulls
• All seackicks to be Xytel or Bronze as specified in A.B.Y.C. recommendations
• Engine and generator raw water intakes to have slotted water scoops and Groco ARG or SA or equivalent single water strainers
• All other raw water intakes to have appropriate strainers
• Two four blade bronze propellers to suit
• Cast bronze or welded s.s. struts with cutless shaft bearing, recessed and thru bolted to hull; intermittent shaft bearings as required
• FRP shaft logs and dripless stuffing boxes
• Heavy dual density engine insulation as specified by soundown
• Fireboy engine shutdown system
• Blower ventilation
• Integral FRP oil drip pans under engines

• Deck wash down with 24V pressure pump and accumulator tank and hose taps in cockpit  on foredeck
  

ACCOMMODATIONS

• Main bukkheads and faces veneered, painted or formica covered
• Marine grade plywood FRP overlaid to hull and deck
• All interior joinery of the highest yacht quality
• All interior woodwork finished in satin finish varnish or paint as required
• All accommodations and locker doors framed in solid wood
• Vanished teak and holly sole
• Removable overhead panels
• All exposed interior FRP surfaces in cabins, topsides and lockers covered
• All latches, hinges, catches, and pulls to be chromed brass, bronze or polished stainless steel
• Corian counter tops in heads and staterooms
• Upholstery as required; 5" foam sttee cushions, 6" berth mattresses
• Two hi-lo upholstered chairs for use at aft gally counter
• Deck fills and vents for fuel, water, and waste tanks as required
• Watertight deck receptacles, P&S, for shore connection of 110V 100 Amp
• Electrical power, telephone and TV cable
• Deck scuppers, freeing ports, and drains as required
• Painted extruded aluminium mast, spreaders and boom rigging
• 24V electrical winch capable of hoisting dinghy
• Painted fabricated aluminium chocks and dinghy
• Varnished teak ensign and burgee staffs
  

 PROPANE

• 10 lb. propane tank & regulator for BBQ (optional) installed locker venting overboard
• All hoses & connections to Coast Guard requirements
  

ELECTRICAL

• Navigation lights - Coast Guard approved side lights, steaming light, and stern light
• Masthead anchor light and spreader deck lights
• Searchlight, remote controlled, Guest "Beamer" or equivalent
• Miscellaneous deck lights and courtesy lights as required

• Fluorescent lights behind valence over galley couter
• Chromed brass dome lights in each accom. space, galley, heads, engine room and utility space
• Directional chromed brass reading lights in each stateroom and main cabin
• Courtesy lights at steps, in hanging lockers, and as otherwise required
• All wiring sized and color coded to ABYC reccommendations
• Enclosure boxes and wiring for 2 x 8D engine start and 4 x 8D house batteries
• Explosion proof master battery selection switches and req'd
• Appropriate switches and wiring for paralleling batteries
• 24V / 60 amp engine alternators with regulators and charging isolators
• 24V D.C. Custom distribution panel with magnetic breakers & LED lights, with amp main D.C breaker, branch circuits, battery condition volt meter & test switch, load current ammeter, polarity protector
• 12V DC Custom distribution panel, as necessary
• Watertight 12V receptacles at fly bridge helm station
• Interior 12V receptacles as required

• Fischer Panda 16 KW Genset with staring battery, water lift muffler & exhaust separator
• Statpower 3,00W 24V/110V inverter/ battery charger
• Custom 110V AC distribution panel with 100 amp double pole sharper man breaker, AC branch circuits, AC line voltage meter, AC load current am meter, red and green polarity indicator lights
• GFI 110V receptacles in galley, heads, utility space, and each cabin
• 110V four burner glass cook top in galley
• Mocrowave/ Convection oven

• receptacles and wiring for land and cellular telephone, TV and computer as required